This openwork sliding gate combines protection and design. Width 586 cm. Width between pillar: 562 cm. Height 163cm. Anthracite gray color. RAL7016.
Accessories: Cylinder lock. 2 keys. End stop. Upper guide with 6 nylon rollers. Reception stop. 6 casters. Aluminum rail 11.3 m. Screws. Posts not included. Height of the pillars minimum 175 cm.
Supplied as a kit. Clear instructions, quick and easy assembly. You can automate the gate with a sliding gate motor. Find all the characteristics in the technical sheet.
The EIFEL posts in thermo-lacquered aluminum have been specially designed for the installation of a swinging or sliding gate or even a gate.
Practical, the finishing cap of our EIFEL posts can be easily installed and removed to allow you to pass electrical wires in the event of motorization of your gate, gate or for the installation of motorization accessories (flash light, photocells, ...)
This 20x20cm EIFEL post with a height of 190cm is suitable for all aluminum gates and gates not exceeding 180cm in height.
Colours: Anthracite gray (RAL 7016) Material: Aluminum Post height: 1.90 m Pole section: 20 x 20 cm Section of the patina: 25 x 25 cm Installation method: To screw or seal Maximum height of the gate to be installed: 180cm
Accessories included: - Plastic finishing cap with fixing screws (Anthracite grey) - Expansion bolts (for floor fixing)
Advice :
Weight of the gate less than 80kg: You can fix your post by screwing the post fixing plate to the ground (bolts included in our kits) *
Weight of the gate greater than 80 kg: It is recommended to concrete and steel the EIFEL post in order to consolidate it (see technical diagram).
* In the case of hollow posts, we advise you to fix the plate using 10x120mm anchoring studs, for a stronger and more secure fixing. In the case of concrete posts, you can completely fix your post using the bolts included in our kits
Compatible with all CASANOOV gates and gates of height 160 and 180 cm The EIFEL 20x20cm post is available in a height of 166cm. Also available in section: 10x10cm; 15x15cm
If your installation requires several posts, you will find in the "Gate Accessories" category promotional offers in the form of a set of 2 or 4 EIFEL posts of your choice.
Clear instructions, simple and quick assembly. Find all the necessary information about this product in the technical characteristics.
The TANKER C600 sliding gate motor is designed for users wishing to motorize their sliding gate to automate its opening and closing. It allows you to transform your gate into an electric sliding gate. This rack-and-pinion motor is suitable for all types of sliding gates that can be motorized. Whether for PVC, wood, aluminum, or iron sliding gates, this automatic system can be installed on all models weighing less than 600 kg.
Here are the main technical specifications of the motor:
Motor voltage: 230V – 370W Input power: 220VAC±10%/110VAC±10% Frequency: 50Hz/60Hz Gear module: M4 Z=16 teeth Output torque: 30.0 Nm Nominal rotation speed: 14,000 rpm Maximum gate weight: 600kg on level ground Magnetic start and end stops Environmental temperature: -25°C ~ +55°C Protection class: IP55 Opening speed: approximately 12 meters per minute Maximum force: 1100N Nylon rack Control card included with the motor.
Accessories included:
- Two 4-button remote controls with protective cover. Batteries are included. - Nylon rack (4m – 12 pieces of 33cm) - Installation and setup manual - 2 quick release keys in case of power outage 1 pair of infrared photocells with the following characteristics: - 'Transmitter' photocell - 'Receiver' photocell - Black ABS material - Infrared with anti-glare 50,000LUX 1 flashing LED light with a power of 3W (equivalent to a power of 30W for an old-generation incandescent bulb) with the following characteristics: - Operating voltage: 12-265 VAC/DC - Load capacity: < 3W - Flashing frequency: 1Hz - Operating temperature: -20°C ~ +60°C - IP rating: IP54
Tanker C600 motorization features : - Opening according to your choice: left to right (factory mode) or right to left. - Automatic closing: After opening, the gate will automatically close after 0, 10, 30, or 60 seconds, depending on your choice. - Pedestrian mode: The gate opens only partially and then closes after 0, 5, 10, or 30 seconds. - Condominium mode: This mode allows you to reduce settings and configure up to 50 remote controls. Each remote control will control: button 1 (gate opening), button 2 (gate stopping), button 3 (gate closing), and button 4 (pedestrian mode). Each remote control will operate in the same way. - Adjustable opening and closing sensitivity: Depending on your environment, you can adjust the opening and closing power. - Manual gate unlocking. With the included key, you can disengage the opening of your gate and operate it manually. - Auto-stop. The gate stops if it encounters an obstacle. - The motor cannot be connected to a backup battery. In the event of a power outage, manual unlocking with two keys (included) is possible. This disengages the motor's output pinion and allows you to operate your gate freely.
You can pair this motor with photocells, a flashing light, and an opening push button. Be sure to check the electrical compatibility (voltage in Volts) of your existing accessories if they are not from our website. All our accessories are compatible with all our motors.
Installation Tips:
To successfully connect and configure your motor, proceed step by step and check that it is working properly between each step. If you pair accessories with your C600 motor, check each time that your motor is in working order. Finally, ensure that your electrical connection is properly wired. This will help you operate your installation and prevent electrical leaks. Our Casanoov technical team is here to assist you if needed.
Assembly instructions - KIT-000158
